How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
On this page in the next paragraph you'll find lots of reliable content about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, and sometimes, tiling skills. Changing an old bath tub with a new one is also a moderately tough project. If the old bathtub is conveniently easily accessible, the job can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly require a helper to leave the old tub as well as set in the new one. Make sure you have actually certified on your own for the work and also fit attempting it. Rather than hiring a contractor to take over a halfway-completed job, it is better to consider employing one prior to you start. Opportunities are you may need a specialist plumber to make tube links.
This post will aid you mount a brand-new tub in your restroom if you have currently acquired a brand-new tub and do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material list need to comprise the following:
Preparing for the Installation
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used at the very least once as this will certainly resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall between the bath and also the tiling, leading to issues with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealer can fracture fairly early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on How to Install a Bathtub Yourself, I think sharing that blog post was smart. If you liked our article plz do not forget to share it. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Additional Information
Report this page